Dotmod coils, which e-liquid suits which coil
A fresh pack of five coils, a bottle already open, and a puff that either bites or barely registers. With Dotmod coils, the liquid that suited the old head does not always suit the new one, because each resistance vaporises a different volume. Product pages spell out compatibility, rarely the bottle to pour. This guide starts from the other end, the liquid, and works back to the coil that matches it.
Which Dotmod coils for which e-liquid
The right Dotmod coils follow from the bottle. A 10 ml nic salt calls for a tight draw coil, the 0.7 ohm dotCoil or the 1 ohm dotStick coil. A shortfill topped up with nicotine shots, low in strength and rich in glycerine, calls instead for the 0.3 ohm in restricted direct lung or the 0.15 ohm in direct lung.
Between the two, the 0.6 ohm dotCoil, rated at 18 to 22 W, suits a middle strength in freebase. Strength follows the rule set out in our guide to reading nicotine strength, the more vapour a coil makes, the lower it goes.
Dotmod heads sorted by draw
The range spans four families, the dotAIO coils of the original dotAIO, the dotCoils, the dotStick coils and the dotCoil x SteamCraft. The dotCoils, single mesh with a brass connection, are the ones most vapers come across, and two retailer listings agree on the draw of their values.
| Coil | Wattage found | Draw | Bottle that suits it | Strength guide |
|---|---|---|---|---|
| dotCoil 0.7 Ω | not rated by the maker | tight (MTL) | 10 ml nic salt or freebase | 12 to 20 mg/ml |
| dotStick coil 1 Ω | not rated by the distributor | tight | 10 ml nic salt | 12 to 20 mg/ml |
| dotCoil 0.6 Ω | 18 to 22 W | not settled by listings | 10 ml freebase or a 50/50 base | 6 to 12 mg/ml |
| dotCoil 0.3 Ω | 25 to 40 W | restricted direct lung (RDL) | shortfill with shots | 3 to 6 mg/ml |
| dotCoil 0.15 Ω | above 60 W | direct lung (DL) | high VG shortfill with shots | 0 to 3 mg/ml |
These strength figures are this site’s guide, not instructions from the maker. Dotmod’s own dotCoils page gives no wattage, draw or liquid advice, and the wattage ranges come from retailer listings.
Nic salt and a tight draw, the 0.7 ohm and the dotStick
A tight draw moves little liquid per puff. It therefore copes with the top of the scale, the 10 ml bottles capped at 20 mg/ml in the UK, and that is where nic salt belongs.
The 0.7 ohm dotCoil
Two retailer listings, one French and one British, place the 0.7 ohm in mouth to lung vaping and pair it with nic salts or strong liquids. The British listing adds 50/50 liquids. Of the four dotCoil values, it is the highest in ohms and so the one that vaporises least.
Reaching 12 mg/ml with a shortfill makes little sense on this coil. Starting from a 50 ml shortfill with 18 mg/ml shots, you would need ten shots, a 150 ml mix that is two thirds nicotine shot. A ready to vape 10 ml bottle settles the matter, and our comparison of nic salt and freebase helps pick the form.
dotStick coils and the Nord match
The dotStick coils come in 0.4, 0.7 and 1 ohm, in mesh, in packs of five. The distributor’s own listing declares them compatible with Nord coils and not compatible with the dotStick Revo, which a retailer listing repeats. That same retailer says the 1 ohm suits nic salt e-liquids.
The 0.4 ohm in this family vaporises more than the 1 ohm. A middle strength in freebase suits it better than a 20 mg/ml salt.
Shortfills with shots, what the 0.3 and 0.15 ohm need
The two lowest dotCoils get through plenty of liquid. They call for low strengths, the kind you reach by adding one or two nicotine shots to a shortfill sold without nicotine.
The 0.3 ohm in restricted direct lung
Three listings agree on 25 to 40 W for this value, and two describe it as restricted direct lung, a balance of flavour and vapour. A 50 ml shortfill topped up with one 10 ml shot gives 3.3 mg/ml with a 20 mg shot or 3.0 mg/ml with an 18 mg shot. Two shots give 5.7 or 5.1 mg/ml, if the bottle has room for them. Our page on how many nicotine shots to add sets out the formula.
The 0.15 ohm in direct lung
The 0.15 ohm is built for sub ohm vaping with big clouds. A British listing recommends it with high VG shortfills at higher wattage. A 100 ml shortfill with two 18 mg shots makes 120 ml at 3.0 mg/ml, already high for a coil running above 60 W. One shot, at 1.6 mg/ml, fits this draw better.
The VG ratio each Dotmod coil handles
No maximum ratio for these coils is confirmed by more than one listing. The listings give a direction instead, 50/50 liquids and salts for the 0.7 ohm, high vegetable glycerine (VG) liquids for the 0.15 ohm.
The final ratio also depends on the shots. A 100 ml shortfill at 70VG/30PG topped up with two 50/50 shots holds 80 ml of VG in 120 ml, roughly 67% VG, a mix that suits the 0.15 ohm. On the 0.7 ohm, a 50/50 base or a ready to vape 10 ml bottle is the safer pick, because thick liquid soaks more slowly into the wick of a tight coil.
SteamCraft coils, Dotmod coils without a wick
The fourth family in the range looks nothing like the others. The dotCoil x SteamCraft are pre-wound nichrome (Ni80) wires, sold in pairs, to fit on the deck of the dotRBA X or a compatible rebuildable atomiser, with the cotton left to the user.
Four versions appear on the distributor’s listing, two for a tight draw (1.20 ohm at 5 to 15 W, 0.72 ohm at 10 to 20 W) and two for restricted direct lung (0.32 and 0.30 ohm, 25 to 35 W). Choosing the liquid follows the same logic as with the wicked heads, salts and high strengths at the top of the ohm scale, shortfills with shots at the bottom.
FAQ
Five questions that come up when moving from one Dotmod coil to another, alongside everything above.
Which coil fits the original dotAIO?
The first dotAIO takes its own dotAIO coils, which the distributor lists in 0.3, 0.7 and 1.2 ohm, in single mesh or Kanthal clapton. The same page notes they do not fit the dotAIO V2, which uses dotCoils.
What wattage for a 0.6 ohm dotCoil?
Two retailer listings give 18 to 22 W. Starting at the bottom of that range and stepping up gradually gives the wick time to keep up.
Does the dotPod Max take every dotCoil?
It takes the dotCoil family, but Dotmod’s own page rules out the 0.15 ohm on this pod, as on the dotStick Revo. The 0.3, 0.6 and 0.7 ohm coils are therefore the ones to choose.
How can I tell a Dotmod coil is worn out?
Fading flavour, a burnt taste or less vapour at the same setting point to a clogged wick. A very sweet recipe usually speeds this up.
Can I keep the same bottle when moving from the 0.7 to the 0.3 ohm?
Better not. A 20 mg/ml nic salt on a coil that vaporises far more liquid gives a much heavier puff and a harsher throat hit. A weaker bottle should go with the change of coil.
Dotmod coils, choosing the head from the bottle
The reasoning comes in three steps. The bottle sets the strength and the ratio, the strength points to a draw, and the draw points to a resistance within the family your device accepts. Nic salt goes to the 0.7 or 1 ohm, a shortfill with shots to the 0.3 or 0.15 ohm.
Check the ratio separately, especially after adding shots, and our guide to the VG PG ratio after nicotine shots gives the calculation. Well matched Dotmod coils follow the same logic as any replaceable head, strength first, resistance second.
Related guides
- Nicotine strength, reading the figure on the bottle
- How many nicotine shots, the exact calculation
- Nic salt vs freebase, what actually separates them
- VG PG base mix and the ratio your nicotine shots leave behind
Editorial content for adult readers only. Vaping products can contain nicotine, which is a highly addictive substance. Vaping products are not for sale to anyone under 18 in the UK. This article is not a buying recommendation.